Apply generous even coats with a long pile roller to the natural stone at a coverage rate of 4-5m2 per litre. Do not allow the product to pool or the final appearance may not be even in colour on the paving to be enhanced and sealed This product is not suitable if surfaces have been treated previously with a silicon or stearate based water repellent Fantastically versatile vapour control layer that can be used as part of a complete Easyseal system, or alternatively a torch-on or even single ply roof build.

Paving, Pointing & Grouting We offer a range of pointing and grouting materials for jointing your patio slabs, outdoor paving or driveway including flowable slurry grouts such as UltraScape Flowpoint, brush-in grouts like EasyJoint and gun injected mortar for fine pointing. As well as supplying paving primer, sealants and paving and driveway cleaners. Incredibly easy to apply to your roof, the installation process can be carried out by DIY enthusiasts and professional builders alike Briefly open then close high side valve of the manifold gauge set to allow a little high side liquid to flow through the yellow hose and EasySeal Ultimate tube. With high side valve of the manifold gauge set closed, wait one minute for the yellow hose and EasySeal Ultimate to equalize to suction pressure. Disconnect EasySeal Ultimate from suction service port and from manifold gauge set. Discard or recycle empty injector. Manufactured from a polyester base with an SBS (Styrene Butadiene Styrene) bitumen coating, this Easyseal roofing top sheet also features an upper surface with a special finishing of slate mineral. The release film protects the underneath of the sheet and can easily be removed with ease when installing to BS 8217: 2005, 'Code of Practice for Reinforced bitumen membranes for roofing' and IKO fixing guidelines. Features & Benefits: IKO Easyseal / Coldseal Self-Adhesive Top Sheet Roofing Felt - 6m x 1m Treat any efflorescence or staining before application, allow a few weeks before applying EASYseal BCS to ensure efflorescence doesn’t reappearNo need for naked flames or melted bitumen thanks to the super strong adhesive on the underside of this sheet Attach other end of charging hose to low side service port. As this is done, there will be a very small release of system charge that will purge air from the hose. For those who need to install roofing membranes, but want to avoid the hassle and experience requirements that ‘torch-on’ methods such as hot bitumen or use of naked flames usually bring with them, the BBA approved IKOR Easyseal self-adhesive roofing system is absolutely for you. An extremely versatile product guaranteeing an excellent performance on any flat roof it is applied to, this excellent product is made up of a polyester reinforced aluminium core and a bitumen coating.

EASYSeal BCS can be applied to a variety of concrete paving materials on driveways, paths, walkways and patios. Features & Benefits EASYSeal BCS is ideally applied to a dry surface but can be used on lightly damp – not wet or soaked surfaces, must be free from standing or ponded water specialist cleaning to these Asbestos roofs using our specially designed cleaning unit which removes all moss and lichen, with water filtration system included. After the cleaning process, problem areas can be easily identified Floor Levellers & Preparation We offer a range of single & two-part flexible, reinforced and deep fill floor levellers, bulking concrete, primers and vapour suppressants for preparation of your subfloor prior to tiling or laying floor coverings.A minimum of 3 months should be left after the installation of a new driveway or patio before sealing to ensure that any efflorescence or staining has had time to dissipate

Bedding Mortars We supply a range of fast set, cement & resin based bedding mortars which are ideal for installing manhole covers, utility access covers, frames, highways ironwork and the bonding of granite, sandstone & porphyry setts, paving slabs, flags and bedding kerbs. Our range of high strength, bedding mortars mean roads, footpaths & highways can be reopened to traffic in as little as 40 minutes, meaning less disruption for the general public. The EasySeal self-adhesive roofing system has been designed to remove the requirement for hot bitumen and or naked flames for anyone installing roofing membranes. EasySeal is a two-layer high performance system, which was originally developed for small roofs, such as those over garages, porches, extensions and dormer windows etc. However, the fire-safe benefits of EasySeal are equally applicable for large projects. The self-adhesive application process, using no hot bitumen, gas torches or large amounts of messy liquids, makes it an ideal option for experienced contractors or competent DIY installers alike. Apply a second coat whilst the sandstone remains damp from the first coat. Timing depends on temperatures and the type of stone* (This sealer enhancer is suitable for most types of natural stone).Apply EASY Seal BCS with a brush, roller or low pressure sprayer at a rate of 3m2 per litre for the first coat Frequently Asked Questions About the IKO Easyseal Air and Vapour Control Layer - 1m x 15m What sort of projects can this product be used on?